Planning and Building a Greenhouse

Planning and Building a Greenhouse

Planning and Building a Greenhouse

Careful planning is important before a home greenhouse project is started. Building a greenhouse does not need to be expensive or time-consuming. The final choice of the type of greenhouse will depend on the growing space desired, home architecture, available sites, and costs. The greenhouse must, however, provide the proper environment for growing plants.

The greenhouse should be located where it gets maximum sunlight. The first choice of location is the south or southeast side of a building or shade trees. Sunlight all day is best, but morning sunlight on the east side is sufficient for plants. Morning sunlight is most desirable because it allows the plant’s food production process to begin early; thus growth is maximized. An east side location captures the most November to February sunlight. The next best sites are southwest and west of major structures, where plants receive sunlight later in the day. North of major structures is the least desirable location and is good only for plants that require little light.

Deciduous trees, such as maple and oak, can effectively shade the greenhouse from the intense late afternoon summer sun; however, they should not shade the greenhouse in the morning. Deciduous trees also allow maximum exposure to the winter sun because they shed their leaves in the fall. Evergreen trees that have foliage year round should not be located where they will shade the greenhouse because they will block the less intense winter sun. You should aim to maximize winter sun exposure, particularly if the greenhouse is used all year. Remember that the sun is lower in the southern sky in winter causing long shadows to be cast by buildings and evergreen trees (Figure 1).

Good drainage is another requirement for the site. When necessary, build the greenhouse above the surrounding ground so rainwater and irrigation water will drain away. Other site considerations include the light requirements of the plants to be grown; locations of sources of heat, water, and electricity; and shelter from winter wind. Access to the greenhouse should be convenient for both people and utilities. A workplace for potting plants and a storage area for supplies should be nearby.

Types of Greenhouses

A home greenhouse can be attached to a house or garage, or it can be a freestanding structure. The chosen site and personal preference can dictate the choices to be considered. An attached greenhouse can be a half greenhouse, a full-size structure, or an extended window structure. There are advantages and disadvantages to each type.

Attached Greenhouses

Lean-to. A lean-to greenhouse is a half greenhouse, split along the peak of the roof, or ridge line (Figure 2A), Lean-tos are useful where space is limited to a width of approximately seven to twelve feet, and they are the least expensive structures. The ridge of the lean-to is attached to a building using one side and an existing doorway, if available. Lean-tos are close to available electricity, water and heat. The disadvantages include some limitations on space, sunlight, ventilation, and temperature control. The height of the supporting wall limits the potential size of the lean-to. The wider the lean-to, the higher the supporting wall must be. Temperature control is more difficult because the wall that the greenhouse is built on may collect the sun’s heat while the translucent cover of the greenhouse may lose heat rapidly. The lean-to should face the best direction for adequate sun exposure. Finally, consider the location of windows and doors on the supporting structure and remember that snow, ice, or heavy rain might slide off the roof or the house onto the structure.

Even-span. An even-span is a full-size structure that has one gable end attached to another building (Figure 2B). It is usually the largest and most costly option, but it provides more usable space and can be lengthened. The even-span has a better shape than a lean-to for air circulation to maintain uniform temperatures during the winter heating season. An even-span can accommodate two to three benches for growing crops.

Window-mounted. A window-mounted greenhouse can be attached on the south or east side of a house. This glass enclosure gives space for conveniently growing a few plants at relatively low cost (Figure 2D). The special window extends outward from the house a foot or so and can contain two or three shelves.

Freestanding Structures

Freestanding greenhouses are separate structures; they can be set apart from other buildings to get more sun and can be made as large or small as desired (Figure 2C). A separate heating system is needed, and electricity and water must be installed.

The lowest cost per square foot of growing space is generally available in a freestanding or even-span greenhouse that is 17 to 18 feet wide. It can house a central bench, two side benches, and two walkways. The ratio of cost to the usable growing space is good.

When deciding on the type of structure, be sure to plan for adequate bench space, storage space, and room for future expansion. Large greenhouses are easier to manage because temperatures in small greenhouses fluctuate more rapidly. Small greenhouses have a large exposed area through which heat is lost or gained, and the air volume inside is relatively small; therefore, the air temperature changes quickly in a small greenhouse. Suggested minimum sizes are 6 feet wide by 12 feet long for an even-span or freestanding greenhouse.

Structural Materials

A good selection of commercial greenhouse frames and framing materials is available. The frames are made of wood, galvanized steel, or aluminum. Build-it-yourself greenhouse plans are usually for structures with wood or metal pipe frames. Plastic pipe materials generally are inadequate to meet snow and wind load requirements. Frames can be covered with glass, rigid fiberglass, rigid double-wall plastics, or plastic film. All have advantages and disadvantages. Each of these materials should be considered—it pays to shop around for ideas.

Greenhouse frames range from simple to complex, depending on the imagination of the designer and engineering requirements. The following are several common frames (Figure 3).

Quonset. The Quonset is a simple and efficient construction with an electrical conduit or galvanized steel pipe frame. The frame is circular and usually covered with plastic sheeting. Quonset sidewall height is low, which restricts storage space and headroom.

Gothic. The gothic frame construction is similar to that of the Quonset but it has a gothic shape (Figure 3). Wooden arches may be used and joined at the ridge. The gothic shape allows more headroom at the sidewall than does the Quonset.

Rigid-frame. The rigid-frame structure has vertical sidewalls and rafters for a clear-span construction. There are no columns or trusses to support the roof. Glued or nailed plywood gussets connect the sidewall supports to the rafters to make one rigid frame. The conventional gable roof and sidewalls allow maximum interior space and air circulation. A good foundation is required to support the lateral load on the sidewalls.

Post and rafter and A-frame. The post and rafter is a simple construction of an embedded post and rafters, but it requires more wood or metal than some other designs. Strong sidewall posts and deep post embedment are required to withstand outward rafter forces and wind pressures. Like the rigid frame, the post and rafter design allows more space along the sidewalls and efficient air circulation. The A-frame is similar to the post and rafter construction except that a collar beam ties the upper parts of the rafters together.

Coverings

Greenhouse coverings include long-life glass, fiberglass, rigid double-wall plastics, and film plastics with 1- to 3-year lifespans. The type of frame and cover must be matched correctly.

Glass. Glass is the traditional covering. It has a pleasing appearance, is inexpensive to maintain, and has a high degree of permanency. An aluminum frame with a glass covering provides a maintenance-free, weather-tight structure that minimizes heat costs and retains humidity. Glass is available in many forms that would be suitable with almost any style or architecture. Tempered glass is frequently used because it is two or three times stronger than regular glass. Small prefabricated glass greenhouses are available for do-it-yourself installation, but most should be built by the manufacturer because they can be difficult to construct.

The disadvantages of glass are that it is easily broken, is initially expensive to build, and requires must better frame construction than fiberglass or plastic. A good foundation is required, and the frames must be strong and must fit well together to support heavy, rigid glass.

Fiberglass. Fiberglass is lightweight, strong, and practically hailproof. A good grade of fiberglass should be used because poor grades discolor and reduce light penetration. Use only clear, transparent, or translucent grades for greenhouse construction. Tedlar-coated fiberglass lasts 15 to 20 years. The resin covering the glass fibers will eventually wear off, allowing dirt to be retained by exposed fibers. A new coat of resin is needed after 10 to 15 years. Light penetration is initially as good as glass but can drop off considerably over time with poor grades of fiberglass.

Double-wall plastic. Rigid double-layer plastic sheets of acrylic or polycarbonate are available to give long-life, heat-saving covers. These covers have two layers of rigid plastic separated by webs. The double-layer material retains more heat, so energy savings of 30 percent are common. The acrylic is a long-life, nonyellowing material; the polycarbonate normally yellows faster, but usually is protected by a UV-inhibitor coating on the exposed surface. Both materials carry warranties for 10 years on their light transmission qualities. Both can be used on curved surfaces; the polycarbonate material can be curved the most. As a general rule, each layer reduces light by about 10 percent. About 80 percent of the light filters through double-layer plastic, compared with 90 percent for glass.

Film plastic. Film-plastic coverings are available in several grades of quality and several different materials. Generally, these are replaced more frequently than other covers. Structural costs are very low because the frame can be lighter and plastic film is inexpensive. Light transmission of these film-plastic coverings is comparable to glass. The films are made of polyethylene (PE), polyvinyl chloride (PVC), copolymers, and other materials. A utility grade of PE that will last about a year is available at local hardware stores. Commercial greenhouse grade PE has ultraviolet inhibitors in it to protect against ultraviolet rays; it lasts 12 to 18 months. Copolymers last 2 to 3 years. New additives have allowed the manufacture of film plastics that block and reflect radiated heat back into the greenhouse, as does glass which helps reduce heating costs. PVC or vinyl film costs two to five times as much as PE but lasts as long as five years. However, it is available only in sheets four to six feet wide. It attracts dust from the air, so it must be washed occasionally.

Foundations and Floors

Permanent foundations should be provided for glass, fiberglass, or the double-layer rigid-plastic sheet materials. The manufacturer should provide plans for the foundation construction. Most home greenhouses require a poured concrete foundation similar to those in residential houses. Quonset greenhouses with pipe frames and a plastic cover use posts driven into the ground.

Permanent flooring is not recommended because it may stay wet and slippery from soil mix media. A concrete, gravel, or stone walkway 24 to 36 inches wide can be built for easy access to the plants. The rest of the floor should be covered by several inches of gravel for drainage of excess water. Water also can be sprayed on the gravel to produce humidity in the greenhouse.

Environmental Systems

Greenhouses provide a shelter in which a suitable environment is maintained for plants. Solar energy from the sun provides sunlight and some heat, but you must provide a system to regulate the environment in your greenhouse. This is done by using heaters, fans, thermostats, and other equipment.

The heating requirements of a greenhouse depend on the desired temperature for the plants grown, the location and construction of the greenhouse, and the total outside exposed area of the structure. As much as 25 percent of the daily heat requirement may come from the sun, but a lightly insulated greenhouse structure will need a great deal of heat on a cold winter night. The heating system must be adequate to maintain the desired day or night temperature.

Usually the home heating system is not adequate to heat an adjacent greenhouse. A 220-volt circuit electric heater, however, is clean, efficient, and works well. Small gas or oil heaters designed to be installed through a masonry wall also work well.

Solar-heater greenhouses were popular briefly during the energy crisis, but they did not prove to be economical to use. Separate solar collection and storage systems are large and require much space. However, greenhouse owners can experiment with heat-collecting methods to reduce fossil-fuel consumption. One method is to paint containers black to attract heat, and fill them with water to retain it. However, because the greenhouse air temperature must be kept at plant-growing temperatures, the greenhouse itself is not a good solar-heat collector.

Heating systems can be fueled by electricity, gas, oil, or wood. The heat can be distributed by forced hot air, radiant heat, hot water, or steam. The choice of a heating system and fuel depends on what is locally available, the production requirements of the plants, cost, and individual choice. For safety purposes, and to prevent harmful gases from contacting plants, all gas, oil, and woodburning systems must be properly vented to the outside. Use fresh-air vents to supply oxygen for burners for complete combustion. Safety controls, such as safety pilots and a gas shutoff switch, should be used as required. Portable kerosene heaters used in homes are risky because some plants are sensitive to gases formed when the fuel is burned.

Calculating heating system capacity. Heating systems are rated in British thermal units (Btu) per hour (h). The Btu capacity of the heating system, Q, can be estimated easily using three factors:

  1. A is the total exposed (outside) area of the greenhouse sides, ends, and roof in square feet (ft 2 ). On a Quonset, the sides and roof are one unit; measure the length of the curved rafter (ground to ground) and multiply by the length of the house. The curves end area is 2 (ends) X 2/3 X height X width. Add the sum of the first calculation with that of the second.
  2. u is the heat loss factor that quantifies the rate at which heat energy flows out of the greenhouse. For example, a single cover of plastic or glass has a value of 1.2 Btu/h x ft 2 x o F (heat loss in Btu’s her hour per each square foot of area per degree in Fahrenheit); a double-layer cover has a value of 0.8 Btu/h x ft 2 x o F. The values allow for some air infiltration but are based on the assumption that the greenhouse is fairly airtight.
  3. (Ti-To ) is the maximum temperature difference between the lowest outside temperature (To ) in your region and the temperature to be maintained in the greenhouse (Ti ). For example, the maximum difference will usually occur in the early morning with the occurrence of a 0 o F to -5 o F outside temperature while a 60 o F inside temperature is maintained. Plan for a temperature differential of 60 to 65 o F. The following equation summarizes this description: Q =A x u x (Ti-To ).

Example. If a rigid-frame or post and rafter freestanding greenhouse 16 feet wide by 24 feet long, 12 feet high at the ridge, with 6 feet sidewalls, is covered with single-layer glass from the ground to the ridge, what size gas heater would be needed to maintain 60 o F on the coldest winter night (0 o F)? Calculate the total outside area (Figure 4):

two long sides

2 x 6 ft x 24 ft = 288 ft 2


Leave a Reply