ASTEC ASTEC® Re-Ply™ Roofing Systemfor Metal Roofs

ASTEC ASTEC® Re-Ply™ Roofing Systemfor Metal Roofs
  1. Prepare Surface

Tighten or replace loose fasteners. Remove scaling rust and pressure wash to achieve a clean, sound roof surface.

  • Encapsulate Corrosion as Needed

    Apply ASTEC B-16-71 Rust Control specially formulated to neutralize and halt further metal roof corrosion.

  • Seal Fasteners

    Tighten or replace any loose fasteners. Encapsulate every fastener with ASTEC WPM #9 fluid membrane to insure a watertight seal.

  • Seal Seams & Flashings

    Reinforce all seams, flashings, and penetrations with high tensile strength fabric saturated with ASTEC WPM #9 fluid membrane, or use WPM #10 fiber-reinforced fluid membrane.

  • Apply First Layer

    Apply the first layer of either ASTEC #900 Ceramic Finish, or ASTEC #2000 Finish for a tough, weatherproof membrane.

  • Apply Final Layer

    Apply the second application of either ASTEC #900 or ASTEC #2000 Re-Ply finish to the roof. This results in a seamless, highly reflective "cool roof" that remains durable, weathertight, and pliable. Impervious to many airborne corrosives, ASTEC roofs have proven performance over 100’s of millions of square feet.

  • This is a typical system for metal roofs. Products and procedures may vary by roof type and condition. Only ASTEC detailed specifications will be approved on any ASTEC roofing project.

    ASTEC Rust Control  is specially formulated to neutralize and halt further rust corrosion on all rusted surfaces. It prepares and sets the metal for embedding in subsequent ASTEC surface coatings. "> ASTEC Waterproof Sealer WPM #9  is a fluid applied membrane which encases all roof  seams, fastners, joints, flashings, intrusions, and substrate repairs inside a tough, pliable, seamless surface. The renewed surface is now wind and water tight, and ready to be bonded with Astec ceramic finish layers for the ultimate in durable protection from UV sunlight, heat, and airborne corrosives. "> ASTEC Fibered WPM #10 is a fluid-applied weathertight membrane with high solids and fiber reinforcement which dries to a tough, yet flexible monolithic surface. It seamlessly seals seams, fasteners, joints, flashings, intrusions, and repairs against water penetration. WPM #10 is a superior base coat for sustainable ASTEC fluid-applied top coats for roofs and walls."> ASTEC #2000 Finish  works with ASTEC Re-Ply Base Sealer #2000. The first finish layer bonds with the base sealer and melds into the old EPDM roofing material forming a new, seamless, weather tight roofing surface. Once the second layer of Re-Ply #2000 Finish cures, the new roof takes on the sustainable ASTEC advantages that permit the ICC water tight renewable warranty to be updated every ten years. "> ASTEC Ceramic Finish #900  provides the Astec system with it’s durability as well as all its UV, heat, and energy saving advantages. It is deliberately applied in multiple layers to assure a well-bonded seamless surface over ASTEC water tight base sealers. ASTEC #900 surfaces can be tinted in a myriad of coordinating colors that are water based, fade resistant, and easily maintained over the life of the 10 Year Limited Warranty. ">

    ASTEC Re-Ply Products for Metal Substrate Systems

    Hover over any product label for a product description.

    1. Prepare Surface

    Tighten or replace loose fasteners. Remove scaling rust and pressure wash to achieve a clean, sound roof surface.

  • Encapsulate Corrosion as Needed

    Apply ASTEC B-16-71 Rust Control specially formulated to neutralize and halt further metal roof corrosion.

  • Seal Fasteners

    Tighten or replace any loose fasteners. Encapsulate every fastener with ASTEC WPM #9 fluid membrane to insure a watertight seal.

  • Seal Seams & Flashings

    Reinforce all seams, flashings, and penetrations with high tensile strength fabric saturated with ASTEC WPM #9 fluid membrane, or use WPM #10 fiber-reinforced fluid membrane.

  • Apply First Layer

    Apply the first layer of either ASTEC #900 Ceramic Finish, or ASTEC #2000 Finish for a tough, weatherproof membrane.

  • Apply Final Layer

    Apply the second application of either ASTEC #900 or ASTEC #2000 Re-Ply finish to the roof. This results in a seamless, highly reflective "cool roof" that remains durable, weathertight, and pliable. Impervious to many airborne corrosives, ASTEC roofs have proven performance over 100’s of millions of square feet.

  • This is a typical system for metal roofs. Products and procedures may vary by roof type and condition. Only ASTEC detailed specifications will be approved on any ASTEC roofing project.

    ASTEC Rust Control  is specially formulated to neutralize and halt further rust corrosion on all rusted surfaces. It prepares and sets the metal for embedding in subsequent ASTEC surface coatings. "> ASTEC Waterproof Sealer WPM #9  is a fluid applied membrane which encases all roof  seams, fastners, joints, flashings, intrusions, and substrate repairs inside a tough, pliable, seamless surface. The renewed surface is now wind and water tight, and ready to be bonded with Astec ceramic finish layers for the ultimate in durable protection from UV sunlight, heat, and airborne corrosives. "> ASTEC Fibered WPM #10 is a fluid-applied weathertight membrane with high solids and fiber reinforcement which dries to a tough, yet flexible monolithic surface. It seamlessly seals seams, fasteners, joints, flashings, intrusions, and repairs against water penetration. WPM #10 is a superior base coat for sustainable ASTEC fluid-applied top coats for roofs and walls."> ASTEC #2000 Finish  works with ASTEC Re-Ply Base Sealer #2000. The first finish layer bonds with the base sealer and melds into the old EPDM roofing material forming a new, seamless, weather tight roofing surface. Once the second layer of Re-Ply #2000 Finish cures, the new roof takes on the sustainable ASTEC advantages that permit the ICC water tight renewable warranty to be updated every ten years. "> ASTEC Ceramic Finish #900  provides the Astec system with it’s durability as well as all its UV, heat, and energy saving advantages. It is deliberately applied in multiple layers to assure a well-bonded seamless surface over ASTEC water tight base sealers. ASTEC #900 surfaces can be tinted in a myriad of coordinating colors that are water based, fade resistant, and easily maintained over the life of the 10 Year Limited Warranty. ">

    ASTEC Re-Ply Products for Metal Substrate Systems

    Hover over any product label for a product description.


    Leave a Reply